航拍云台G3-3D搭载方法--5iflying测评室

admin

云台如何搭载在飞行器上呢？

How to mount gimbal to aircraft?

第一种方法：通过挂载件搭载。这就要了解我们云台挂载件数据：

First method :Mounted by hanginghook.So that we need to know the data of hanging hook.

1.  两根云台管之间相距（外径）：64mm

Distance between two tubes(OD:outside diameter):64mm

2.  两根云台管之间相距（内径）：44.2mm

Distance between two tubes(ID: inner diameter):44.2mm.

3.  单管外径：10mm

Single tube OD:10mm

可搭载在轴距为380MM 450MM 550MM 650MM 700MM 800MM这些飞行器上。

以下以飞客MH-550为例：

It can be mounted on wheelbase of aircraft: 380mm,450mm ,550mm ,650mm ,700mm ,800mm.

Take MH-550 as an example

1.  准备一个XT60 母头。

Prepare a female XT60.

2.  云台两个焊接线分别对齐母头正负极加锡并上热缩膜（以母头正负极标识为准：云台红线焊正极，云台黑线焊负极）。

Cover shrink film with tin after gimbal’s two welding line alignfemale’s positive and negative separately.(Take female’s positive and negative asidentification: Red cable welding positive electrode,black cable welding negative electrode.)

3.  准备好自己的1分2电源接头，一头连接在云台电源母头上为云台供电，另一头为飞机动力供电。

Prepare 2 in 1 power connector,one side power supply for gimbalwhich connect female,another side power supply for aircraft.

4.  用螺丝（云台挂载件固定螺丝）连接飞行器挂载件与云台上板后，套入云台管后锁紧螺丝（挂载件自锁螺丝）。

After connect aircraft’s hanging hook and gimbal’s upper board withscrews(fixed screws for hanging hook of gimbal),insert gimbal tube  and fasten screws(self-locking screws forhanging hook)

5.  组装减振球，即完成云台搭载.以下以X4-550MM通过云台挂载件搭载云台为示例。

Assembly vibration dampers,then gimbal mounting is completed. In the following X4-550MM gimbal mounted by hanginghook as an example.

6.  将云台电源线与天蝎底板（PCB板）上的云台焊点相焊接，红线焊正极，黑线焊负极。

Welding power cable and solder joint of X4-550MM PCB.Red cablewelding positive electrode,black cable welding negativeelectrode.

7.  对照云台板孔位组装减振球。通过减振球连接飞行器与云台。

Reference holes position of gimbal board toaccembly vibration dampers.Connectaircraft and gimbal by vibration dampers.

8.  只需2个步骤组装完成。（如上图）

第二种方法：通过底板搭载。以精灵2为例：

Only need 2 steps to complete assembly.(As shown above)

The 2nd method:Mounted by bottom aboard.we takePhantom 2 as example.

1.  云台降压模块从精灵主控板上取电：红线与红线焊在一起，黑线与黑线焊在一起。

Step-down module of gimbal is powered by mainboard of Phantom 2:welding red cables together,welding black cables together.

2.  在箭头指向的空白处固定好降压模块。

Fixed step-down module on the blank space which the arrow points.

3.  根据螺丝孔位，对云台上板进行钻孔处理，锁定螺丝固定云台上板。即可通过减振球搭载云台完成组装。~~~~准备完成，美图手到擒来......

According to screws holes position, Drilling upper aboard of gimbal and fasten screws to fix it.Completeassembly after vibration dampers mounted on gimbal……Complete preparation.

飞客云台采用独立GCU芯片，高精度控制，即插即用的三轴云台。专为Gopro及同尺寸运动相机倾力打造。超高性价比与您一起换个角度看世界。

Flycker use independent GCU,high precision control system ,plug-and-play 3-axis gimbal.Designed for Gopro and other same size sportscamera with high performance to price ratio. Let’s see the world from another angle !

小郭

好专业的讲解

JokerZ

双语字幕,太牛了

武杰

一多少钱一个

武杰

好宝贝